[2023] HQT-4180 All-in-One Exam Guide Practice To your HQT-4180 Exam!
Preparations of HQT-4180 Exam 2023 Hitachi Vantara Qualified Professional Unlimited 37 Questions
NEW QUESTION # 11
Which two statements are correct when adding cache to a VSP E590? (Choose two.)
- A. This is not supported online.
- B. Cache Modules must be installed on the CM board.
- C. CMG0 and CMG1 must have the same DIMM type.
- D. Cache modules must be installed in CMG1.
Answer: C,D
NEW QUESTION # 12
A customer wants to upgrade a VSP G700 to 512 GB RAM capacity.
What is the valid CFM configuration?
- A. two BM35 per system
- B. one BM45 per controller
- C. two BM35 per controller
- D. two BM45 per controller
Answer: D
NEW QUESTION # 13
A customer wants to upgrade their VSP E790 with a SAS Expansion feature.
What are three requirements? (Choose three.)
- A. Two additional Disk Boards (DKBs) have to be installed.
- B. Slots B of both controllers must be available for DKB installation.
- C. The SAS Expansion license has to be installed.
- D. Drive Boxes (DBs) with SAS interface have to be added.
- E. In Shared Memory, the Extension1 has to be enabled.
Answer: A,C,D
NEW QUESTION # 14
A drive in a 3D + 1P RAID group fails in a VSP G700 and there is no spare drive available.
Which two actions are automatically performed by the system? (Choose two.)
- A. The RAID group is placed in Correction Access.
- B. The Correction Copy process starts.
- C. An alert is generated.
- D. Dynamic Sparing is started.
Answer: C,D
NEW QUESTION # 15
What are two valid back-end SAS cable connections on a VSP midrange system? (Choose two.)
- A. from DKA to DKB
- B. from DKA to SSW
- C. from ENC to ENC
- D. from DKB to ENC
Answer: A,D
NEW QUESTION # 16
The SVP of a VSP G900 system failed and you have been asked to replace it.
Which two items must be available to perform the replacement? (Choose two.)
- A. the Hitachi Remote Ops Monitor Agent iso file
- B. the iso file with the correct version of Hitachi Ops Center
- C. the iso file with the correct version of the Windows operating system
- D. the microcode iso file with the correct software versions
Answer: B,D
NEW QUESTION # 17
Which program is used to perform the "New Installation" procedure on a VSP F700 system?
- A. raidcom CLI
- B. MPC connected to the maintenance LAN port
- C. Hitachi Ops Center Administrator
- D. SVP Web console
Answer: C
NEW QUESTION # 18
Which tool do you use to install license keys on a VSP G370 system?
- A. MPC Software
- B. Maintenance Utility
- C. HSA Embedded
- D. Storage Navigator
Answer: B
NEW QUESTION # 19
What are two consequences when a "New Installation" procedure is performed on a VSP Midrange system? (Choose two.)
- A. The MPC software is updated.
- B. All the data on RAID groups is lost.
- C. The SVP drive is formatted.
- D. The license keys are deleted.
Answer: B,C
NEW QUESTION # 20
Which program is used to perform the "New Installation" procedure on a VSP midrange system?
- A. GUM
- B. Webconsole
- C. BECK
- D. MPC
Answer: A
NEW QUESTION # 21
Your customer wants to connect multiple servers to a new port on a VSP G700. The correct topology has already been set for the port.
What should you do next?
- A. Create a Host Group.
- B. Enable Host Group security.
- C. Scan for all WWNs.
- D. Enable Port Security.
Answer: C
NEW QUESTION # 22
You are installing a new VSP G700 and are using the Initial Setup Wizard (ISW) for the network configuration.
Which set of IP addresses is configured with the ISW?
- A. IP addresses of all the ports
- B. IP addresses of maintenance ports
- C. IP addresses of management ports
- D. IP addresses of all the ports and of the SVP
Answer: C
NEW QUESTION # 23
You need to replace a broken fan in a VSP E1090.
What is the correct procedure?
- A. Use the MPC for blocking the fan, then replace it.
- B. Use Storage Navigator for blocking the fan, then replace it.
- C. Remove the broken fan, then replace it.
- D. Use the Maintenance Utility for stopping the fan, then replace it.
Answer: C
NEW QUESTION # 24
You are installing a VSP F370 and you need to connect your laptop to one of the controllers.
What are the two default IP addresses of the maintenance ports of CTL1 and CTL2? (Choose two.)
- A. 192.168.0.16
- B. 192.168.0.17
- C. 10.0.0.16
- D. 10.0.0.17
Answer: A,C
NEW QUESTION # 25
......
Focus on HQT-4180 All-in-One Exam Guide For Quick Preparation: https://www.testsdumps.com/HQT-4180_real-exam-dumps.html
Practice To HQT-4180 - TestsDumps Remarkable Practice On your Hitachi Vantara Qualified Professional - VSP Midrange Family Installation Exam: https://drive.google.com/open?id=17omOG46SYpL68RyDkCe8GyZOzHRiznIa
