Certification Training for 300-510 Exam Dumps Test Engine [2021]
Oct 29, 2021 Step by Step Guide to Prepare for 300-510 Exam
Audience, Prerequisites, and Objectives for Implementing Cisco Service Provider Advanced Routing Solutions Training
Particularly, this course for exam 300-510 invigorates the needs of network administrators, project managers, system engineers, and network designers. The initial requirements they need to meet before undertaking the training are such as having at least intermediate knowledge covering Cisco IOS or Cisco IOS XE as well as Cisco IOS XR Software that touches on the configuration. More requirements include awareness of networking concerning IPv6 and IPv4 TCP/IP, intermediate knowledge about routing protocols of OSPF, BGP, and ISIS, and comprehension regarding MPLS technologies, multicast technologies, and segment routing. Also, there are other vital courses that one ought to have passed through before this specific training. This is to gain the proper perspective about what they are about to learn and ensure this goes on effectively. Overall, on completing this 300-510 exam course, you will have mastered the following objectives:
- Abilities in configuring route redistribution;
- Implementing advanced features so that there is enhanced convergence within BGP networks;
- Putting into practice mechanisms targeting dynamic RP (Rendezvous Point) distribution.
- Putting into operation and authenticating the protocol known as PIM-SM;
- Describing and comparing core concepts for multicast;
- Executing and authenticating technology for segment routing within an interior gateway protocol;
- Troubleshooting ISIS, OSPF, and BGP;
- Executing security options for BGP;
- Using IPv6 mechanisms for tunneling;
- Describing the usage of traffic engineering within networks for segment routing;
- Capabilities in configuring BGP so that it can connect upstream SP or customers successfully to the SP network;
- Executing MSDP within the interdomain surrounding;
- Potentiality in executing advanced features in relation with OSPFv2 that run in SP networks;
- Capabilities in executing advanced features concerning multilevel ISIS that run in SP networks;
- Comprehension of protocols for routing that are usually utilized in SP environments;
- Configuring BGP scalability within SP networks;
- Implementing enhanced PIM-SM associated features;
- Implementing and troubleshooting traffic engineering for MPLS;
- Deploying and verifying MPLS;
The skills covered when practicing with the hands-on labs for exam 300-510 include executing Special Area Types for OSPF, implementing Multiarea IS-IS, route redistribution, route selection for BGP, route reflectors, security options for BGP, and troubleshooting routing protocols. Others are executing MPLS within the SP core, deploying MPLS TE for Cisco, configuring and authenticating segment routing for IGP, and operating with tunnels aimed at IPv6. Candidates will also draw practical skills in the areas of enabling and optimizing PIM-SM, executing enhancements for PIM-SM, and putting into practice RP distribution.
Difficulty in Writing Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Exam
The Implementation of the Cisco Service Provider VPN Services (300-510) certification is one of the most important certifications that applicants can have on their CV. One of the biggest challenges for many candidates is to use the Internet to find so many details that make it impossible for them to believe, which would be beneficial for them to choose the correct 300-510 SPRI practice test.
However, applicants can clear the examination with the correct concentration and the correct preparatory material. TestsDumps have the most up to date 300-510 SPRI dumps that allows a clear understanding of the pattern in questions raised by these dumping aspirants with real certification. The experts track qualification questions for all the changes in the course. Certification problems also require realistic research, which is an ideal forum to test the knowledge that is collected. For the study content, refer to the links below.
Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Certification Path
Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) exam is affiliated with the CCNP Service Provider and Cisco Accredited Professional-Service Provider VPN Services Implementation certifications. This is the official prerequisite for this exam. However, the course, Integrating VPN Services from Cisco Service Provider, allows applicants to prepare for this exam and is highly recommended.
NEW QUESTION 10
Refer to the exhibit
Which router does R1 install as an alternate next hop when trying to reach R3 if LFA is enabled?
- A. R3
- B. R2
- C. R4
- D. R5
Answer: B
NEW QUESTION 11
Refer to the exhibit.
Router 1 is a core ABR in a Cisco Unified MPLS environment. All of the router 1 BGP peers are established, but traffic between customers is failing. Which BGP configuration must be added to the configuration?
- A. It must be configured with a route reflector
- B. It must be configured for graceful restart
- C. It must be configured with PIC edge
- D. It must be configured with send labels
Answer: D
NEW QUESTION 12
Refer to the exhibit.
Traffic flow from router R1 to router R6 is delay-sensitive It must consider potential link-failure and node-failure conditions Which configuration must an engineer apply to router R1 to route traffic to router R6 if router R2 fails?
- A. Option D
- B. Option A
- C. Option C
- D. Option B
Answer: D
NEW QUESTION 13
Refer to the exhibit.
XR1 and XR2 are sending the prefix 10.11.11.0/24 to XR3. A configured policy on XR1 is incorrectly prepending AS path 11 11 12 12 onto this prefix. A network operator wants to add a policy onto XR3 that will not allow the falsely prepending prefix from being installed. Which policy configuration applied to the XR3 neighbor configuration for XR1 can accomplish this requirement without impact to other or future received routes?
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: A
Explanation:
Reference:
b_routing_cr41crs/b_routing_cr41crs_chapter_01000.html#wp3850885229
NEW QUESTION 14
Refer to the exhibit.
A network operator is working to deploy a Unified BGP design and allow it to be available only in selected markets and services in the future. The label allocation is not functioning as desired. Which action will fix the issue?
- A. Remove the allocate-labels command.
- B. Remove the route policy and only configure "allocate-label".
- C. Reconfigure the route-policy ALL_LABELS to match all after the drop.
- D. Reconfigure the route-policy ALL_LABELS to pass.
Answer: D
NEW QUESTION 15
Refer to the exhibit.
What is the relationship between Router 1 and Router 2?
- A. Router 1 centrally learns the topology of the network to aid in SR-TE path selection, and Router 2 is a node that feeds Router 1 topology information.
- B. Router 1 and Router 2 centrally learn the topology of the network to aid in SR-TE path selection for peers.
- C. Router 2 is the head-end router in an SR-TE tunnel, and it is learning topology of the network from the PCE enabled on Router 1.
- D. Router 1 and Router 2 are participating in SR-TE tunnels and are both head-end routers.
Answer: C
NEW QUESTION 16
Refer to the exhibit.
After troubleshooting BGP traffic steering issue, which action did the network operator take to achieve the correct effect of this configuration?
- A. Routes that have passed through AS 65517 have the local preference set to 150 and the traffic is denied.
- B. Routes that have passed through AS 65517 have the local preference set to 150.
- C. Routes that have originated through AS 65517 have the local preference set to 150.
- D. Routes directly attached to AS 65517 have the local preference set to 150.
Answer: B
NEW QUESTION 17
For which reason can two devices fail to establish an OSPF neighbor relationship?
- A. The two devices have different network types
- B. The two devices have different process IDs
- C. The two devices have the same area ID
- D. The two devices have different router IDs
Answer: A
Explanation:
Reference:
https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13699-29.html
NEW QUESTION 18 
Refer to the exhibit. A network operator must inject a Level 1 route from XR2 (10.16.16.0/24) into the ISIS topology. Which configuration allows the injection in a way that XR3 and XR1 have a valid and working route for 10.16.16.0/24?
- A.
- B.
- C.
- D.
Answer: B
Explanation:
Explanation
NEW QUESTION 19
Refer to the exhibit.
A network operators configuring BGP PIC on CE1 on already established neighborships with PE1ana PE2 inside the fully converged MPLS network Which element needs to be implemented to make this feature function effectively?
- A. BGP import export policies must be applied on all devices for the routes needing BGP for PIC
- B. The operator must ensure that all prefixes have the same next-hop from PE1 and PE2 for BGP PICA reserved BGP
- C. Bidirectional Forwarding Detection must be applied to the upstream facing BGP interfaces.
- D. community of 1 10 must be used to denote the PIC feature set to the routing protocol
Answer: C
NEW QUESTION 20 
Refer to the exhibit. R1 is directly connected to R2 and R3. R1 is in BGP AS 123, R2 is in BGP AS 2, and R3 is in BGP AS 3. Assume that there is no connectivity issue between R1, R2 and R1, R3. Which result between BGP peers R1, R2 and R1, R3 is true?
- A. The BGP session comes up between R1 and R2 and between R1 and R3.
- B. The BGP session comes up between R1 and R3, but not between R1 and R2.
- C. The BGP session does not come up between R1 and R2 and between R1 and R3.
- D. The BGP session comes up between R1 and R2, but not between R1 and R3.
Answer: A
NEW QUESTION 21
Refer to the exhibit.
A network engineer implemented this segment routing configuration. Which statement about the output is true?
- A. This range conflicts with the segment routing local block range.
- B. The device must be reloaded for these ranges to be allocated and used.
- C. A nondefault segment routing global block range is being used on this device.
- D. The default segment routing global block range is being used on this device.
Answer: C
NEW QUESTION 22
Which two statements about route reflectors are true? (Choose two.)
- A. If a router received an iBGP route with the originator-ID attribute set to its own router ID, the route is discarded.
- B. Routes received from nonclient peers are reflected to route reflector clients as well as nonclient peers.
- C. Routes received from a route reflector client is reflected to other clients and nonclient peers.
- D. If a route reflector receives a route with a cluster-list attribute containing a different cluster ID, the route is discarded.
- E. Routes received from nonclient peers are reflected to route reflector cluster as well as OSPF peers.
Answer: A,C
Explanation:
Explanation/Reference: http://www.networkers-online.com/blog/2009/02/bgp-route-reflector-basics/
NEW QUESTION 23
Drag and drop the attributes for the BGP route selection on the left into the correct order on the right. Not all options are used.
Answer:
Explanation:
NEW QUESTION 24
Refer to the exhibit.
Which attribute can router 1 alter so that only other iBGP peers prefer to use 192.168.4.2 as the next hop for route 192.168.3.0/24?
- A. origin
- B. weight
- C. MED
- D. local preference
Answer: C
NEW QUESTION 25 
Refer to the exhibit. CE1 and CE2 cannot communicate through the service provider BGP peering is established between PE1 and PE2. IS-IS is the only routing protocol running in the service provider core. What step can be done to troubleshoot the issue?
- A. Switch the IGPs running in the core from IS-IS to OSPF to support a Cisco MPLS TE tunnel from PE1 to PE2.
- B. Verify the MPLS LSPs.
- C. Configure BGP between CE and PE routers.
- D. Confirm that IS-IS is running with metric-style narrow.
Answer: D
NEW QUESTION 26
Refer to the exhibit.
Which attribute can router 1 alter so that only other iBGP peers prefer to use 192.168.4.2 as the next hop for route 192.168.3.0/24?
- A. origin
- B. weight
- C. MED
- D. local preference
Answer: C
NEW QUESTION 27
For which reason can two devices fail to establish an OSPF neighbor relationship?
- A. The two devices have different network types
- B. The two devices have different process IDs
- C. The two devices have the same area ID
- D. The two devices have different router IDs
Answer: A
Explanation:
Explanation/Reference: https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13699-29.html
NEW QUESTION 28
For which reason can two BGP peers fail to establish a neighbor relationship?
- A. Their BGP send-community strings are misconfigured
- B. Their BGP timers are mismatched
- C. They are both activated under an IPv4 address family
- D. Their remote-as numbers are misconfigured
Answer: D
Explanation:
Explanation/Reference:
NEW QUESTION 29
......
Ultimate Guide to Prepare 300-510 Certification Exam for CCNP Service Provider: https://www.testsdumps.com/300-510_real-exam-dumps.html
CCNP Service Provider 300-510 Real Exam Questions and Answers FREE Updated: https://drive.google.com/open?id=1LH9eiTQ1D9jnEqJL100-voSwkRZ98BJ7
