First Attempt Guaranteed Success in NACE-CIP2-001 Exam 2023
Real NACE-CIP2-001 Exam Questions are the Best Preparation Material
NEW QUESTION 51
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Cold flow or creep
- B. Cohesion failure
- C. Glue failure
- D. Adhesion failure
Answer: A
NEW QUESTION 52
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. linings protect the contents and the container.
- B. linings are more durable than coatings.
- C. coatings are more durable than linings.
- D. coatings are expected to degrade over time.
Answer: A
NEW QUESTION 53
A reinforced coating is
- A. equally resistant to abrasion and impact as a non-reinforced coating.
- B. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- C. equally resistant to movement and impact as a non-reinforced coating.
- D. more resistant to movement, abrasion, and impact than a non-reinforced coating.
Answer: D
NEW QUESTION 54
Coating surveys may include which steps?
Select All That Apply:
- A. Summarize the collected data
- B. Develop a survey plan
- C. Evaluate the coatings performance
- D. Schedule the remedial work
Answer: A,B,C,D
NEW QUESTION 55
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. True
- B. False
Answer: B
NEW QUESTION 56
The primary purpose of Fireproofing coatings are to provide:
- A. Temporary protection for the structure
- B. Explosion resistance
- C. fire extinguishing characteristics
- D. Preferential fuel for the fire
Answer: A
NEW QUESTION 57
External coatings applied to buried pipelines are generally tested for:
- A. Gloss level
- B. Solvent resistance
- C. Chalking resistance
- D. Cathodic disbondment
Answer: D
NEW QUESTION 58
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Different than air blast cleaning
- B. The same as air blast cleaning
- C. Comparable to air blast cleaning
- D. Slightly different to air blast cleaning
Answer: B
NEW QUESTION 59
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. manufacturer of the equipment.
- B. coating type.
- C. time of the year (winter/summer).
- D. type of dehumidification equipment (refrigerant or desiccant).
Answer: B
NEW QUESTION 60
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.
- A. False
- B. True
Answer: B
NEW QUESTION 61
The most likely area of failure on a buried external pipeline coating is the:
- A. Areas exposed to Ultra Violet light
- B. Mainline coating
- C. Field joint coating
- D. Ground bed
Answer: C
NEW QUESTION 62
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Coal Tar Enamel
- B. 3-Layer Polyethylene (PE)
- C. Fusion Bonded Epoxy
- D. 2-Layer Polyethylene (PE)
Answer: B
NEW QUESTION 63
When conducting inspections the Inspector should follow which standards:
- A. Australian standards in Australia
- B. The specified standards
- C. NACE and SSPC standards in North America
- D. ISO standards in Europe and Asia
Answer: B
NEW QUESTION 64
The best choice of instrument for holiday testing of thick film concrete coatings is:
- A. Low Voltage Sponge Type
- B. High Voltage AC
- C. High Voltage DC Pulse Type
- D. High Voltage DC Constant Current
Answer: D
NEW QUESTION 65
NACE No.13/ SSPC 6 identifies the use of:
- A. Abrasive blasting only
- B. Watterjetting only
- C. Steam cleaning only
- D. Various methods of cleaning
Answer: D
NEW QUESTION 66
In the event of a conflict between the Product Data Sheet and the Specification:
- A. It is up to the Applicator to decide which one to follow
- B. The Specification prevails
- C. The Product Data Sheet prevails
- D. It is up to the Inspector to decide which one to follow
Answer: B
NEW QUESTION 67
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Review the standard with the Contractor and re-inspect the floor
- B. Shut the job down
- C. Request that the Contractor re-blast the floor
- D. Call your supervisor
Answer: A
NEW QUESTION 68
A single component water borne acrylic coating cures by:
- A. Oxidation
- B. Co-Reaction
- C. Solvent Evaporation
- D. Coalescence
Answer: D
NEW QUESTION 69
Ideally, documentation requirements should be defined:
- A. At the pre-job conference
- B. By the inspector
- C. By the contractor
- D. In the specification
Answer: D
NEW QUESTION 70
Cold-applied tape
- A. is polyethylene film, heat laminated, 'With an adhesive layer of butyl glue.
- B. are identifiable by its distinct colors, usually light blue, green, Or Grey.
- C. have a cross-linked polyethylene backing and a heat-activated adhesive.
- D. is typically green or led and looks like "painted" finish.
Answer: A
NEW QUESTION 71
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. It contains biocide
- B. The floating structure is stationary
- C. It will result in a very slippery surface
- D. It doesn't contain biocide
Answer: A
NEW QUESTION 72
NACE International Standards are developed by:
- A. Government mandates
- B. Regional mandates
- C. Standard committees
- D. International mandates
Answer: C
NEW QUESTION 73
Corrosion is the reverse process of
- A. steel manufacturing.
- B. hot dipping.
- C. galvanic deterioration.
- D. flaking.
Answer: A
NEW QUESTION 74
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Supervision Costs
- B. Lower Application Costs
- C. Lower Safety Enforcement Costs
- D. Lower Coating Life Cycle Costs
Answer: D
NEW QUESTION 75
......
Practice LATEST NACE-CIP2-001 Exam Updated 100 Questions: https://www.testsdumps.com/NACE-CIP2-001_real-exam-dumps.html
Download Latest NACE-CIP2-001 Dumps with Authentic Real Exam QA's: https://drive.google.com/open?id=110FiYRKvW-r-yGtkbVjOP9EOTODQX8jc
