[Jan 21, 2022] Get to the Top with NACE-CIP2-001 Practice Exam Questions
Use Real NACE-CIP2-001 Dumps Free Sample Questions and Practice Test Engine
NEW QUESTION 58
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method B - X cut
- B. Method A - X Cut
- C. Method A - Cross Hatch
- D. Method B - Cross Hatch
Answer: B
NEW QUESTION 59
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. run through the air wash separator.
- B. disposed of properly.
- C. washed with clean potable water prior to Use.
- D. mixed with uncontaminated abrasive
Answer: B
NEW QUESTION 60
External coatings applied to buried pipelines are generally tested for:
- A. Solvent resistance
- B. Chalking resistance
- C. Gloss level
- D. Cathodic disbondment
Answer: D
NEW QUESTION 61
Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:
- A. Conductive coatings applied to a cementitious substrate
- B. Non-Conductive coatings applied to a conductive metallic substrate
- C. Conductive coatings applied to a magnetic metallic substrate
- D. Magnetic coatings applied to a magnetic metallic substrate
Answer: B
NEW QUESTION 62
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Cure stage
- B. Flow stage
- C. Wetting stage
- D. Gel stage
Answer: B
NEW QUESTION 63
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.
- A. False
- B. True
Answer: B
NEW QUESTION 64
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Slightly different to air blast cleaning
- B. Comparable to air blast cleaning
- C. The same as air blast cleaning
- D. Different than air blast cleaning
Answer: C
NEW QUESTION 65
The primary purpose of Fireproofing coatings are to provide:
- A. Explosion resistance
- B. Preferential fuel for the fire
- C. fire extinguishing characteristics
- D. Temporary protection for the structure
Answer: D
NEW QUESTION 66
When using a destructive Paint Inspection Gauge the NACE inspector must:
- A. Determine the Dry Film Thickness of the coating prior to use
- B. Ensure the glue on the dolly is properly applied prior to use
- C. Consult SSPC Guide 1 prior to use
- D. Select the appropriate hand wheel based on the measured Dry Film Thickness prior to us
Answer: A
NEW QUESTION 67
The Concrete Repair Institute's comparators can be used to assess:
- A. Compressive and tensile strength prior to coating
- B. Surface profile prior to coating
- C. Surface cleanliness prior to coating
- D. Contamination levels prior to coating
Answer: B
NEW QUESTION 68
NACE Standards include:
- A. a) & b)
- B. Material Requirements
- C. Standard Practices
- D. a) only
Answer: A
NEW QUESTION 69
Examples of non-ferrous metals include
Select All that Apply:
- A. mild steel.
- B. iron
- C. copper
- D. aluminum
Answer: C,D
NEW QUESTION 70
Coating surveys may include which steps?
Select All That Apply:
- A. Summarize the collected data
- B. Evaluate the coatings performance
- C. Schedule the remedial work
- D. Develop a survey plan
Answer: A,B,C,D
NEW QUESTION 71
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Magnetic Gauge
- B. Eddy Current Gauge
- C. Ultra Sonic DFT Gauge
- D. Tooke Gauge
Answer: D
NEW QUESTION 72
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Ignore the additional requirement
- B. Request clarification from the specifier
- C. Enforce the additional requirement
- D. Call your supervisor
Answer: C
NEW QUESTION 73
A failure caused by applying a coating too thinly is known as
- A. cracking.
- B. pinholes.
- C. chalking.
- D. failure to cure.
Answer: B
NEW QUESTION 74
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. Sacking
- B. High-pressure water washing
- C. Stoning
- D. Acid etching
Answer: A
NEW QUESTION 75
Individuals conducting Coating Surveys should:
- A. Always be NACE or SSPC Protective coating Specialists
- B. Always be experienced Specification Writers
- C. Always be NACE Level 3 Certified Inspectors
- D. Always be trained and experienced Coating Industry
Answer: D
NEW QUESTION 76
NACE Level 2 Inspectors have been authorized to perform:
- A. Visual inspection, Non-Destructive and Destructive testing
- B. Visual inspection only
- C. Visual inspection and Non-destructive testing
- D. All types of inspection without supervision
Answer: A
NEW QUESTION 77
NACE International Standards are developed by:
- A. Standard committees
- B. Government mandates
- C. Regional mandates
- D. International mandates
Answer: A
NEW QUESTION 78
Surface preparation of concrete is performed using:
- A. Methods that are exactly the same as steel
- B. Methods that have been modified for concrete
- C. Methods that are the same as wood
- D. Methods that are completely different to steel
Answer: B
NEW QUESTION 79
When a coating is expected to be exposed to temperatures above 93C (200 F) the best choice would be:
- A. Latex
- B. Organic coatings
- C. Inorganic Coatings
- D. Polyurea
Answer: C
NEW QUESTION 80
Linings are used on the interior of pipelines to
- A. afford limited temperature insulation.
- B. protect the transported product.
- C. provide protection against soil chemicals.
- D. reduce magnetic polarity.
Answer: B
NEW QUESTION 81
The most likely area of failure on a buried external pipeline coating is the:
- A. Ground bed
- B. Field joint coating
- C. Areas exposed to Ultra Violet light
- D. Mainline coating
Answer: B
NEW QUESTION 82
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. False
- B. True
Answer: A
NEW QUESTION 83
......
Pass NACE NACE-CIP2-001 exam - questions - convert Tets Engine to PDF: https://www.testsdumps.com/NACE-CIP2-001_real-exam-dumps.html
2022 Realistic Verified Free NACE NACE-CIP2-001 Exam Questions : https://drive.google.com/open?id=1eyG4X4aHTw7vnRn3eELilYdZVPiKABrt
